/* USER CODE BEGIN Header */
|
/**
|
******************************************************************************
|
* @file gpio.c
|
* @brief This file provides code for the configuration
|
* of all used GPIO pins.
|
******************************************************************************
|
* @attention
|
*
|
* Copyright (c) 2023 STMicroelectronics.
|
* All rights reserved.
|
*
|
* This software is licensed under terms that can be found in the LICENSE file
|
* in the root directory of this software component.
|
* If no LICENSE file comes with this software, it is provided AS-IS.
|
*
|
******************************************************************************
|
*/
|
/* USER CODE END Header */
|
|
/* Includes ------------------------------------------------------------------*/
|
#include "gpio.h"
|
|
/* USER CODE BEGIN 0 */
|
|
/* USER CODE END 0 */
|
|
/*----------------------------------------------------------------------------*/
|
/* Configure GPIO */
|
/*----------------------------------------------------------------------------*/
|
/* USER CODE BEGIN 1 */
|
|
/* USER CODE END 1 */
|
|
/** Configure pins as
|
* Analog
|
* Input
|
* Output
|
* EVENT_OUT
|
* EXTI
|
*/
|
void MX_GPIO_Init(void)
|
{
|
|
GPIO_InitTypeDef GPIO_InitStruct = {0};
|
|
/* GPIO Ports Clock Enable */
|
__HAL_RCC_GPIOH_CLK_ENABLE();
|
__HAL_RCC_GPIOC_CLK_ENABLE();
|
__HAL_RCC_GPIOA_CLK_ENABLE();
|
__HAL_RCC_GPIOB_CLK_ENABLE();
|
__HAL_RCC_GPIOD_CLK_ENABLE();
|
|
/*Configure GPIO pin Output Level */
|
HAL_GPIO_WritePin(GPIOC, StripLights_Pin|mikrobus_an_Pin|RS485_Dir_Pin|CAN_STB_Pin
|
|mikrobus_sck_Pin|mikrobus_miso_Pin|mikrobus_mosi_Pin, GPIO_PIN_RESET);
|
|
/*Configure GPIO pin Output Level */
|
HAL_GPIO_WritePin(SPI1_CS_GPIO_Port, SPI1_CS_Pin, GPIO_PIN_SET);
|
|
/*Configure GPIO pin Output Level */
|
HAL_GPIO_WritePin(GPIOB, LedBlue_Pin|WiFiRst_Pin, GPIO_PIN_SET);
|
|
/*Configure GPIO pin Output Level */
|
HAL_GPIO_WritePin(GPIOB, mikrobus_scl_Pin|mikrobus_sda_Pin|mikrobus_int_Pin|mikrobus_rst_Pin, GPIO_PIN_RESET);
|
|
/*Configure GPIO pin Output Level */
|
HAL_GPIO_WritePin(GPIOC, LedGreen_Pin|LedRed_Pin, GPIO_PIN_SET);
|
|
/*Configure GPIO pin Output Level */
|
HAL_GPIO_WritePin(mikrobus_cs_GPIO_Port, mikrobus_cs_Pin, GPIO_PIN_RESET);
|
|
/*Configure GPIO pin Output Level */
|
HAL_GPIO_WritePin(Relay_GPIO_Port, Relay_Pin, GPIO_PIN_RESET);
|
|
/*Configure GPIO pins : PCPin PCPin PCPin PCPin
|
PCPin PCPin PCPin PCPin
|
PCPin */
|
GPIO_InitStruct.Pin = StripLights_Pin|mikrobus_an_Pin|LedGreen_Pin|RS485_Dir_Pin
|
|CAN_STB_Pin|LedRed_Pin|mikrobus_sck_Pin|mikrobus_miso_Pin
|
|mikrobus_mosi_Pin;
|
GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
|
GPIO_InitStruct.Pull = GPIO_NOPULL;
|
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
|
HAL_GPIO_Init(GPIOC, &GPIO_InitStruct);
|
|
/*Configure GPIO pin : PtPin */
|
GPIO_InitStruct.Pin = mikrobus_pwm_Pin;
|
GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
|
GPIO_InitStruct.Pull = GPIO_NOPULL;
|
HAL_GPIO_Init(mikrobus_pwm_GPIO_Port, &GPIO_InitStruct);
|
|
/*Configure GPIO pins : PAPin PAPin */
|
GPIO_InitStruct.Pin = SPI1_CS_Pin|mikrobus_cs_Pin;
|
GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
|
GPIO_InitStruct.Pull = GPIO_NOPULL;
|
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
|
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
|
|
/*Configure GPIO pins : PBPin PBPin PBPin PBPin
|
PBPin PBPin */
|
GPIO_InitStruct.Pin = LedBlue_Pin|mikrobus_scl_Pin|mikrobus_sda_Pin|WiFiRst_Pin
|
|mikrobus_int_Pin|mikrobus_rst_Pin;
|
GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
|
GPIO_InitStruct.Pull = GPIO_NOPULL;
|
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
|
HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
|
|
/*Configure GPIO pins : PBPin PBPin PBPin */
|
GPIO_InitStruct.Pin = Key1_Pin|Key2_Pin|Key3_Pin;
|
GPIO_InitStruct.Mode = GPIO_MODE_IT_FALLING;
|
GPIO_InitStruct.Pull = GPIO_NOPULL;
|
HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
|
|
/*Configure GPIO pin : PtPin */
|
GPIO_InitStruct.Pin = Relay_Pin;
|
GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
|
GPIO_InitStruct.Pull = GPIO_NOPULL;
|
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
|
HAL_GPIO_Init(Relay_GPIO_Port, &GPIO_InitStruct);
|
|
/* EXTI interrupt init*/
|
HAL_NVIC_SetPriority(EXTI15_10_IRQn, 0, 0);
|
HAL_NVIC_EnableIRQ(EXTI15_10_IRQn);
|
|
}
|
|
/* USER CODE BEGIN 2 */
|
|
/* USER CODE END 2 */
|
