/**
|
******************************************************************************
|
* @file stm8s_gpio.h
|
* @author MCD Application Team
|
* @version V2.3.0
|
* @date 16-June-2017
|
* @brief This file contains all functions prototype and macros for the GPIO peripheral.
|
******************************************************************************
|
* @attention
|
*
|
* <h2><center>© COPYRIGHT 2014 STMicroelectronics</center></h2>
|
*
|
* Licensed under MCD-ST Liberty SW License Agreement V2, (the "License");
|
* You may not use this file except in compliance with the License.
|
* You may obtain a copy of the License at:
|
*
|
* http://www.st.com/software_license_agreement_liberty_v2
|
*
|
* Unless required by applicable law or agreed to in writing, software
|
* distributed under the License is distributed on an "AS IS" BASIS,
|
* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
|
* See the License for the specific language governing permissions and
|
* limitations under the License.
|
*
|
******************************************************************************
|
*/
|
|
/* Define to prevent recursive inclusion -------------------------------------*/
|
#ifndef __STM8S_GPIO_H
|
#define __STM8S_GPIO_H
|
|
/* Includes ------------------------------------------------------------------*/
|
#include "stm8s.h"
|
|
/* Exported variables ------------------------------------------------------- */
|
/* Exported types ------------------------------------------------------------*/
|
|
/** @addtogroup GPIO_Exported_Types
|
* @{
|
*/
|
|
/**
|
* @brief GPIO modes
|
*
|
* Bits definitions:
|
* - Bit 7: 0 = INPUT mode
|
* 1 = OUTPUT mode
|
* 1 = PULL-UP (input) or PUSH-PULL (output)
|
* - Bit 5: 0 = No external interrupt (input) or No slope control (output)
|
* 1 = External interrupt (input) or Slow control enabled (output)
|
* - Bit 4: 0 = Low level (output)
|
* 1 = High level (output push-pull) or HI-Z (output open-drain)
|
*/
|
typedef enum
|
{
|
GPIO_MODE_IN_FL_NO_IT = (uint8_t)0x00, /*!< Input floating, no external interrupt */
|
GPIO_MODE_IN_PU_NO_IT = (uint8_t)0x40, /*!< Input pull-up, no external interrupt */
|
GPIO_MODE_IN_FL_IT = (uint8_t)0x20, /*!< Input floating, external interrupt */
|
GPIO_MODE_IN_PU_IT = (uint8_t)0x60, /*!< Input pull-up, external interrupt */
|
GPIO_MODE_OUT_OD_LOW_FAST = (uint8_t)0xA0, /*!< Output open-drain, low level, 10MHz */
|
GPIO_MODE_OUT_PP_LOW_FAST = (uint8_t)0xE0, /*!< Output push-pull, low level, 10MHz */
|
GPIO_MODE_OUT_OD_LOW_SLOW = (uint8_t)0x80, /*!< Output open-drain, low level, 2MHz */
|
GPIO_MODE_OUT_PP_LOW_SLOW = (uint8_t)0xC0, /*!< Output push-pull, low level, 2MHz */
|
GPIO_MODE_OUT_OD_HIZ_FAST = (uint8_t)0xB0, /*!< Output open-drain, high-impedance level,10MHz */
|
GPIO_MODE_OUT_PP_HIGH_FAST = (uint8_t)0xF0, /*!< Output push-pull, high level, 10MHz */
|
GPIO_MODE_OUT_OD_HIZ_SLOW = (uint8_t)0x90, /*!< Output open-drain, high-impedance level, 2MHz */
|
GPIO_MODE_OUT_PP_HIGH_SLOW = (uint8_t)0xD0 /*!< Output push-pull, high level, 2MHz */
|
}GPIO_Mode_TypeDef;
|
|
/**
|
* @brief Definition of the GPIO pins. Used by the @ref GPIO_Init function in
|
* order to select the pins to be initialized.
|
*/
|
|
typedef enum
|
{
|
GPIO_PIN_0 = ((uint8_t)0x01), /*!< Pin 0 selected */
|
GPIO_PIN_1 = ((uint8_t)0x02), /*!< Pin 1 selected */
|
GPIO_PIN_2 = ((uint8_t)0x04), /*!< Pin 2 selected */
|
GPIO_PIN_3 = ((uint8_t)0x08), /*!< Pin 3 selected */
|
GPIO_PIN_4 = ((uint8_t)0x10), /*!< Pin 4 selected */
|
GPIO_PIN_5 = ((uint8_t)0x20), /*!< Pin 5 selected */
|
GPIO_PIN_6 = ((uint8_t)0x40), /*!< Pin 6 selected */
|
GPIO_PIN_7 = ((uint8_t)0x80), /*!< Pin 7 selected */
|
GPIO_PIN_LNIB = ((uint8_t)0x0F), /*!< Low nibble pins selected */
|
GPIO_PIN_HNIB = ((uint8_t)0xF0), /*!< High nibble pins selected */
|
GPIO_PIN_ALL = ((uint8_t)0xFF) /*!< All pins selected */
|
}GPIO_Pin_TypeDef;
|
|
/**
|
* @}
|
*/
|
|
/* Exported constants --------------------------------------------------------*/
|
/* Exported macros -----------------------------------------------------------*/
|
/* Private macros ------------------------------------------------------------*/
|
|
/** @addtogroup GPIO_Private_Macros
|
* @{
|
*/
|
|
/**
|
* @brief Macro used by the assert function to check the different functions parameters.
|
*/
|
|
/**
|
* @brief Macro used by the assert function in order to check the different
|
* values of GPIOMode_TypeDef.
|
*/
|
#define IS_GPIO_MODE_OK(MODE) \
|
(((MODE) == GPIO_MODE_IN_FL_NO_IT) || \
|
((MODE) == GPIO_MODE_IN_PU_NO_IT) || \
|
((MODE) == GPIO_MODE_IN_FL_IT) || \
|
((MODE) == GPIO_MODE_IN_PU_IT) || \
|
((MODE) == GPIO_MODE_OUT_OD_LOW_FAST) || \
|
((MODE) == GPIO_MODE_OUT_PP_LOW_FAST) || \
|
((MODE) == GPIO_MODE_OUT_OD_LOW_SLOW) || \
|
((MODE) == GPIO_MODE_OUT_PP_LOW_SLOW) || \
|
((MODE) == GPIO_MODE_OUT_OD_HIZ_FAST) || \
|
((MODE) == GPIO_MODE_OUT_PP_HIGH_FAST) || \
|
((MODE) == GPIO_MODE_OUT_OD_HIZ_SLOW) || \
|
((MODE) == GPIO_MODE_OUT_PP_HIGH_SLOW))
|
|
/**
|
* @brief Macro used by the assert function in order to check the different
|
* values of GPIO_Pins.
|
*/
|
#define IS_GPIO_PIN_OK(PIN) ((PIN) != (uint8_t)0x00)
|
|
/**
|
* @}
|
*/
|
|
/* Exported functions ------------------------------------------------------- */
|
/** @addtogroup GPIO_Exported_Functions
|
* @{
|
*/
|
|
void GPIO_DeInit(GPIO_TypeDef* GPIOx);
|
void GPIO_Init(GPIO_TypeDef* GPIOx, GPIO_Pin_TypeDef GPIO_Pin, GPIO_Mode_TypeDef GPIO_Mode);
|
void GPIO_Write(GPIO_TypeDef* GPIOx, uint8_t PortVal);
|
void GPIO_WriteHigh(GPIO_TypeDef* GPIOx, GPIO_Pin_TypeDef PortPins);
|
void GPIO_WriteLow(GPIO_TypeDef* GPIOx, GPIO_Pin_TypeDef PortPins);
|
void GPIO_WriteReverse(GPIO_TypeDef* GPIOx, GPIO_Pin_TypeDef PortPins);
|
uint8_t GPIO_ReadInputData(GPIO_TypeDef* GPIOx);
|
uint8_t GPIO_ReadOutputData(GPIO_TypeDef* GPIOx);
|
BitStatus GPIO_ReadInputPin(GPIO_TypeDef* GPIOx, GPIO_Pin_TypeDef GPIO_Pin);
|
void GPIO_ExternalPullUpConfig(GPIO_TypeDef* GPIOx, GPIO_Pin_TypeDef GPIO_Pin, FunctionalState NewState);
|
/**
|
* @}
|
*/
|
|
#endif /* __STM8L_GPIO_H */
|
|
|
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
|
