update yocto build.sh to yocto package

guowenxue

2023-03-30 328883219b417fc2f03281f58d41cb0a444e44e2

 bsp/bootloader/patch/uboot-imx-lf-5.15.32-2.0.0.patch

@@ -33,7 +33,7 @@
+   phy-reset-post-delay = <15>;
    status = "okay";
 };
 

@@ -91,14 +94,17 @@
    pinctrl-0 = <&pinctrl_enet2>;
    phy-mode = "rmii";
@@ -42,11 +42,11 @@
+   phy-reset-duration = <50>;
+   phy-reset-post-delay = <15>;
    status = "okay";
 

    mdio {
       #address-cells = <1>;
       #size-cells = <0>;
 

-      ethphy0: ethernet-phy@2 {
-         reg = <2>;
+      ethphy0: ethernet-phy@0 {
@@ -56,13 +56,13 @@
          clock-names = "rmii-ref";
@@ -151,21 +157,21 @@
    status = "okay";
 

    display0: display@0 {
-      bits-per-pixel = <24>;
-      bus-width = <24>;
+      bits-per-pixel = <16>;
+      bus-width = <16>;
 

       display-timings {
          native-mode = <&timing0>;
          timing0: timing0 {
@@ -84,11 +84,11 @@
+         vback-porch = <32>;
+         vfront-porch = <13>;
+         vsync-len = <3>;
 

          hsync-active = <0>;
          vsync-active = <0>;
@@ -284,6 +290,40 @@
 

 &iomuxc {
    pinctrl-names = "default";
+   pinctrl-0 = <&pinctrl_extgpio>;
@@ -125,7 +125,7 @@
+         MX6UL_PAD_SNVS_TAMPER9__GPIO5_IO09   0x17059 /* 40# GPIO */
+      >;
+   };
 

    pinctrl_csi1: csi1grp {
       fsl,pins = <
@@ -312,6 +352,7 @@
@@ -135,7 +135,7 @@
+         MX6UL_PAD_SNVS_TAMPER7__GPIO5_IO07 0x10B0 /* ENET1 RESET */
       >;
    };
 

@@ -327,6 +368,7 @@
          MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00   0x1b0b0
          MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01   0x1b0b0
@@ -143,7 +143,7 @@
+         MX6UL_PAD_SNVS_TAMPER4__GPIO5_IO04   0x10B0 /* ENET2 RESET */
       >;
    };
 

@@ -384,13 +426,6 @@
          MX6UL_PAD_LCD_DATA14__LCDIF_DATA14  0x79
          MX6UL_PAD_LCD_DATA15__LCDIF_DATA15  0x79
@@ -157,7 +157,7 @@
-         MX6UL_PAD_LCD_DATA23__LCDIF_DATA23  0x79
       >;
    };
 

@@ -423,7 +458,6 @@
          MX6UL_PAD_JTAG_TRST_B__SAI2_TX_DATA   0x11088
          MX6UL_PAD_JTAG_TCK__SAI2_RX_DATA   0x11088
@@ -165,7 +165,7 @@
-         MX6UL_PAD_SNVS_TAMPER4__GPIO5_IO04   0x17059
       >;
    };
 

@@ -448,7 +482,6 @@
       fsl,pins = <
          MX6UL_PAD_BOOT_MODE0__GPIO5_IO10   0x70a1
@@ -179,7 +179,7 @@
+++ uboot-imx-lf-5.15.32-2.0.0/arch/arm/dts/Makefile   2022-09-04 15:05:50.936174546 +0800
@@ -871,6 +871,7 @@
    imx6ull-kontron-n641x-s.dtb
 

 dtb-$(CONFIG_MX6ULL) += \
+   igkboard.dtb \
    imx6ull-14x14-ddr3-val.dtb \
@@ -191,7 +191,7 @@
@@ -157,6 +157,16 @@
    prompt "MX6 board select"
    optional
 

+config TARGET_LINGYUN_IGKBOARD
+   bool "LingYun IoT Gateway Kits Board(IGKBoard)"
+   depends on MX6ULL
@@ -210,7 +210,7 @@
 source "board/BuR/brppt2/Kconfig"
 source "board/out4/o4-imx6ull-nano/Kconfig"
+source "board/lingyun/igkboard/Kconfig"
 

 endif
diff -Nuar -x lingyun.bmp uboot-imx/board/lingyun/igkboard/igkboard.c uboot-imx-lf-5.15.32-2.0.0/board/lingyun/igkboard/igkboard.c
--- uboot-imx/board/lingyun/igkboard/igkboard.c   1970-01-01 08:00:00.000000000 +0800
@@ -1257,12 +1257,12 @@
@@ -182,6 +182,8 @@
 {
    int result;
 

+   phy_reset(phydev);
+
    if (phydev->autoneg != AUTONEG_ENABLE)
       return genphy_setup_forced(phydev);
 

diff -Nuar -x lingyun.bmp uboot-imx/include/configs/igkboard.h uboot-imx-lf-5.15.32-2.0.0/include/configs/igkboard.h
--- uboot-imx/include/configs/igkboard.h   1970-01-01 08:00:00.000000000 +0800
+++ uboot-imx-lf-5.15.32-2.0.0/include/configs/igkboard.h   2022-09-04 15:05:50.940174512 +0800
@@ -1538,13 +1538,13 @@
@@ -273,6 +273,9 @@
 CROSS_COMPILE ?=
 endif
 

+ARCH = arm
+CROSS_COMPILE ?= /opt/buildroot/cortexA7/bin/arm-linux-
+
 KCONFIG_CONFIG   ?= .config
 export KCONFIG_CONFIG
 

diff -Nuar -x lingyun.bmp uboot-imx/tools/boot/bootm.c uboot-imx-lf-5.15.32-2.0.0/tools/boot/bootm.c
--- uboot-imx/tools/boot/bootm.c   1970-01-01 08:00:00.000000000 +0800
+++ uboot-imx-lf-5.15.32-2.0.0/tools/boot/bootm.c   2022-09-04 15:05:57.424118419 +0800