update linux kernel build shell script to remove unsed drivers

guowenxue

2023-03-30 95ff6821a02653b7ab8555f7283628cca82881c0

 bsp/bootloader/patch/uboot-imx-lf-5.10.52-2.1.0.patch

@@ -41,7 +41,7 @@
+   phy-reset-post-delay = <15>;
    status = "okay";
 };
 

@@ -91,14 +93,17 @@
    pinctrl-0 = <&pinctrl_enet2>;
    phy-mode = "rmii";
@@ -50,11 +50,11 @@
+   phy-reset-duration = <50>;
+   phy-reset-post-delay = <15>;
    status = "okay";
 

    mdio {
       #address-cells = <1>;
       #size-cells = <0>;
 

-      ethphy0: ethernet-phy@2 {
-         reg = <2>;
+      ethphy0: ethernet-phy@0 {
@@ -68,16 +68,16 @@
    pinctrl-0 = <&pinctrl_lcdif_dat
-           &pinctrl_lcdif_ctrl>;
+          &pinctrl_lcdif_ctrl>;
 

    display = <&display0>;
    status = "okay";
 

    display0: display@0 {
-      bits-per-pixel = <24>;
-      bus-width = <24>;
+      bits-per-pixel = <16>;
+      bus-width = <16>;
 

       display-timings {
          native-mode = <&timing0>;
          timing0: timing0 {
@@ -99,11 +99,11 @@
+         vback-porch = <32>;
+         vfront-porch = <13>;
+         vsync-len = <3>;
 

          hsync-active = <0>;
          vsync-active = <0>;
@@ -284,6 +289,40 @@
 

 &iomuxc {
    pinctrl-names = "default";
+   pinctrl-0 = <&pinctrl_extgpio>;
@@ -140,7 +140,7 @@
+         MX6UL_PAD_SNVS_TAMPER9__GPIO5_IO09   0x17059 /* 40# GPIO */
+      >;
+   };
 

    pinctrl_csi1: csi1grp {
       fsl,pins = <
@@ -306,12 +345,13 @@
@@ -160,7 +160,7 @@
+         MX6UL_PAD_SNVS_TAMPER7__GPIO5_IO07 0x10B0 /* ENET1 RESET */
       >;
    };
 

@@ -321,12 +361,13 @@
          MX6UL_PAD_GPIO1_IO06__ENET2_MDIO   0x1b0b0
          MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN   0x1b0b0
@@ -178,9 +178,9 @@
+         MX6UL_PAD_SNVS_TAMPER4__GPIO5_IO04   0x10B0 /* ENET2 RESET */
       >;
    };
 

@@ -367,41 +408,33 @@
 

    pinctrl_lcdif_dat: lcdifdatgrp {
       fsl,pins = <
-         MX6UL_PAD_LCD_DATA00__LCDIF_DATA00  0x79
@@ -225,7 +225,7 @@
+         MX6UL_PAD_LCD_DATA15__LCDIF_DATA15   0x79
       >;
    };
 

    pinctrl_lcdif_ctrl: lcdifctrlgrp {
       fsl,pins = <
-         MX6UL_PAD_LCD_CLK__LCDIF_CLK       0x79
@@ -241,7 +241,7 @@
+         MX6UL_PAD_SNVS_TAMPER9__GPIO5_IO09   0x79
       >;
    };
 

@@ -409,8 +442,8 @@
       fsl,pins = <
          MX6UL_PAD_NAND_WP_B__QSPI_A_SCLK   0x70a1
@@ -264,14 +264,14 @@
-         MX6UL_PAD_SNVS_TAMPER4__GPIO5_IO04   0x17059
       >;
    };
 

    pinctrl_pwm1: pwm1grp {
       fsl,pins = <
-         MX6UL_PAD_GPIO1_IO08__PWM1_OUT   0x110b0
+         MX6UL_PAD_GPIO1_IO08__PWM1_OUT    0x110b0
       >;
    };
 

@@ -448,7 +480,6 @@
       fsl,pins = <
          MX6UL_PAD_BOOT_MODE0__GPIO5_IO10   0x70a1
@@ -281,7 +281,7 @@
       >;
    };
@@ -486,22 +517,20 @@
 

    pinctrl_usdhc1: usdhc1grp {
       fsl,pins = <
-         MX6UL_PAD_SD1_CMD__USDHC1_CMD        0x17059
@@ -301,7 +301,7 @@
+         MX6UL_PAD_UART1_RTS_B__GPIO1_IO19   0x17059 /* SD1 CD */
       >;
    };
 

    pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
       fsl,pins = <
-         MX6UL_PAD_SD1_CMD__USDHC1_CMD     0x170b9
@@ -312,7 +312,7 @@
          MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x170b9
          MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x170b9
@@ -512,8 +541,8 @@
 

    pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
       fsl,pins = <
-         MX6UL_PAD_SD1_CMD__USDHC1_CMD     0x170f9
@@ -323,7 +323,7 @@
          MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x170f9
          MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x170f9
@@ -523,8 +552,8 @@
 

    pinctrl_usdhc2: usdhc2grp {
       fsl,pins = <
-         MX6UL_PAD_NAND_RE_B__USDHC2_CLK     0x17059
@@ -334,7 +334,7 @@
          MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x17059
          MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x17059
@@ -534,8 +563,8 @@
 

    pinctrl_usdhc2_8bit: usdhc2grp_8bit {
       fsl,pins = <
-         MX6UL_PAD_NAND_RE_B__USDHC2_CLK     0x10069
@@ -345,7 +345,7 @@
          MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x17059
          MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x17059
@@ -549,8 +578,8 @@
 

    pinctrl_usdhc2_8bit_100mhz: usdhc2grp_8bit_100mhz {
       fsl,pins = <
-         MX6UL_PAD_NAND_RE_B__USDHC2_CLK     0x100b9
@@ -356,7 +356,7 @@
          MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x170b9
          MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x170b9
@@ -564,8 +593,8 @@
 

    pinctrl_usdhc2_8bit_200mhz: usdhc2grp_8bit_200mhz {
       fsl,pins = <
-         MX6UL_PAD_NAND_RE_B__USDHC2_CLK     0x100f9
@@ -371,7 +371,7 @@
+++ uboot-imx-lf-5.10.52-2.1.0/arch/arm/dts/Makefile   2022-06-30 20:28:15.839187950 +0800
@@ -779,6 +779,7 @@
    imx6ul-pico-pi.dtb
 

 dtb-$(CONFIG_MX6ULL) += \
+   igkboard.dtb \
    imx6ull-14x14-ddr3-val.dtb \
@@ -383,7 +383,7 @@
@@ -158,6 +158,16 @@
    prompt "MX6 board select"
    optional
 

+config TARGET_LINGYUN_IGKBOARD
+   bool "LingYun IoT Gateway Kits Board(IGKBoard)"
+   depends on MX6ULL
@@ -401,8 +401,8 @@
 source "board/wandboard/Kconfig"
 source "board/warp/Kconfig"
 source "board/BuR/brppt2/Kconfig"
+source "board/lingyun/igkboard/Kconfig"  
 
+source "board/lingyun/igkboard/Kconfig"

 endif
diff -Nuar -x lingyun.bmp uboot-imx/board/lingyun/igkboard/igkboard.c uboot-imx-lf-5.10.52-2.1.0/board/lingyun/igkboard/igkboard.c
--- uboot-imx/board/lingyun/igkboard/igkboard.c   1970-01-01 08:00:00.000000000 +0800
@@ -1459,13 +1459,13 @@
@@ -182,6 +182,9 @@
 {
    int result;
 

+    /*  add Soft Reset the PHY by guowenxue, 2021.11.14 */
+    phy_reset(phydev);
+
    if (phydev->autoneg != AUTONEG_ENABLE)
       return genphy_setup_forced(phydev);
 

diff -Nuar -x lingyun.bmp uboot-imx/include/configs/igkboard.h uboot-imx-lf-5.10.52-2.1.0/include/configs/igkboard.h
--- uboot-imx/include/configs/igkboard.h   1970-01-01 08:00:00.000000000 +0800
+++ uboot-imx-lf-5.10.52-2.1.0/include/configs/igkboard.h   2022-06-30 20:28:15.839187950 +0800
@@ -1768,10 +1768,10 @@
@@ -263,6 +263,9 @@
 CROSS_COMPILE ?=
 endif
 

+ARCH=arm
+CROSS_COMPILE?=/opt/buildroot/cortexA7/bin/arm-linux-
+
 KCONFIG_CONFIG   ?= .config
 export KCONFIG_CONFIG