From aa38e5c1f48e31213ee349aa5cd6f06c85bda70d Mon Sep 17 00:00:00 2001
From: android <android@lingyun.com>
Date: Tue, 25 Jun 2024 21:49:39 +0800
Subject: [PATCH] Add GD32F103RCT6 ADC converter board SDK source code
---
mcu_sdk/gd32f103/rk_eFire/System/Src/system_stm32f1xx.c | 408 ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
1 files changed, 408 insertions(+), 0 deletions(-)
diff --git a/mcu_sdk/gd32f103/rk_eFire/System/Src/system_stm32f1xx.c b/mcu_sdk/gd32f103/rk_eFire/System/Src/system_stm32f1xx.c
new file mode 100644
index 0000000..052bec6
--- /dev/null
+++ b/mcu_sdk/gd32f103/rk_eFire/System/Src/system_stm32f1xx.c
@@ -0,0 +1,408 @@
+/**
+ ******************************************************************************
+ * @file system_stm32f1xx.c
+ * @author MCD Application Team
+ * @brief CMSIS Cortex-M3 Device Peripheral Access Layer System Source File.
+ *
+ * 1. This file provides two functions and one global variable to be called from
+ * user application:
+ * - SystemInit(): Setups the system clock (System clock source, PLL Multiplier
+ * factors, AHB/APBx prescalers and Flash settings).
+ * This function is called at startup just after reset and
+ * before branch to main program. This call is made inside
+ * the "startup_stm32f1xx_xx.s" file.
+ *
+ * - SystemCoreClock variable: Contains the core clock (HCLK), it can be used
+ * by the user application to setup the SysTick
+ * timer or configure other parameters.
+ *
+ * - SystemCoreClockUpdate(): Updates the variable SystemCoreClock and must
+ * be called whenever the core clock is changed
+ * during program execution.
+ *
+ * 2. After each device reset the HSI (8 MHz) is used as system clock source.
+ * Then SystemInit() function is called, in "startup_stm32f1xx_xx.s" file, to
+ * configure the system clock before to branch to main program.
+ *
+ * 4. The default value of HSE crystal is set to 8 MHz (or 25 MHz, depending on
+ * the product used), refer to "HSE_VALUE".
+ * When HSE is used as system clock source, directly or through PLL, and you
+ * are using different crystal you have to adapt the HSE value to your own
+ * configuration.
+ *
+ ******************************************************************************
+ * @attention
+ *
+ * <h2><center>© Copyright (c) 2017 STMicroelectronics.
+ * All rights reserved.</center></h2>
+ *
+ * This software component is licensed by ST under BSD 3-Clause license,
+ * the "License"; You may not use this file except in compliance with the
+ * License. You may obtain a copy of the License at:
+ * opensource.org/licenses/BSD-3-Clause
+ *
+ ******************************************************************************
+ */
+
+/** @addtogroup CMSIS
+ * @{
+ */
+
+/** @addtogroup stm32f1xx_system
+ * @{
+ */
+
+/** @addtogroup STM32F1xx_System_Private_Includes
+ * @{
+ */
+
+#include "stm32f1xx.h"
+
+/**
+ * @}
+ */
+
+/** @addtogroup STM32F1xx_System_Private_TypesDefinitions
+ * @{
+ */
+
+/**
+ * @}
+ */
+
+/** @addtogroup STM32F1xx_System_Private_Defines
+ * @{
+ */
+
+#if !defined (HSE_VALUE)
+ #define HSE_VALUE 8000000U /*!< Default value of the External oscillator in Hz.
+ This value can be provided and adapted by the user application. */
+#endif /* HSE_VALUE */
+
+#if !defined (HSI_VALUE)
+ #define HSI_VALUE 8000000U /*!< Default value of the Internal oscillator in Hz.
+ This value can be provided and adapted by the user application. */
+#endif /* HSI_VALUE */
+
+/*!< Uncomment the following line if you need to use external SRAM */
+#if defined(STM32F100xE) || defined(STM32F101xE) || defined(STM32F101xG) || defined(STM32F103xE) || defined(STM32F103xG)
+/* #define DATA_IN_ExtSRAM */
+#endif /* STM32F100xE || STM32F101xE || STM32F101xG || STM32F103xE || STM32F103xG */
+
+/* Note: Following vector table addresses must be defined in line with linker
+ configuration. */
+/*!< Uncomment the following line if you need to relocate the vector table
+ anywhere in Flash or Sram, else the vector table is kept at the automatic
+ remap of boot address selected */
+/* #define USER_VECT_TAB_ADDRESS */
+
+#if defined(USER_VECT_TAB_ADDRESS)
+/*!< Uncomment the following line if you need to relocate your vector Table
+ in Sram else user remap will be done in Flash. */
+/* #define VECT_TAB_SRAM */
+#if defined(VECT_TAB_SRAM)
+#define VECT_TAB_BASE_ADDRESS SRAM_BASE /*!< Vector Table base address field.
+ This value must be a multiple of 0x200. */
+#define VECT_TAB_OFFSET 0x00000000U /*!< Vector Table base offset field.
+ This value must be a multiple of 0x200. */
+#else
+#define VECT_TAB_BASE_ADDRESS FLASH_BASE /*!< Vector Table base address field.
+ This value must be a multiple of 0x200. */
+#define VECT_TAB_OFFSET 0x00000000U /*!< Vector Table base offset field.
+ This value must be a multiple of 0x200. */
+#endif /* VECT_TAB_SRAM */
+#endif /* USER_VECT_TAB_ADDRESS */
+
+/******************************************************************************/
+
+/**
+ * @}
+ */
+
+/** @addtogroup STM32F1xx_System_Private_Macros
+ * @{
+ */
+
+/**
+ * @}
+ */
+
+/** @addtogroup STM32F1xx_System_Private_Variables
+ * @{
+ */
+
+ /* This variable is updated in three ways:
+ 1) by calling CMSIS function SystemCoreClockUpdate()
+ 2) by calling HAL API function HAL_RCC_GetHCLKFreq()
+ 3) each time HAL_RCC_ClockConfig() is called to configure the system clock frequency
+ Note: If you use this function to configure the system clock; then there
+ is no need to call the 2 first functions listed above, since SystemCoreClock
+ variable is updated automatically.
+ */
+uint32_t SystemCoreClock = 16000000;
+const uint8_t AHBPrescTable[16U] = {0, 0, 0, 0, 0, 0, 0, 0, 1, 2, 3, 4, 6, 7, 8, 9};
+const uint8_t APBPrescTable[8U] = {0, 0, 0, 0, 1, 2, 3, 4};
+
+/**
+ * @}
+ */
+
+/** @addtogroup STM32F1xx_System_Private_FunctionPrototypes
+ * @{
+ */
+
+#if defined(STM32F100xE) || defined(STM32F101xE) || defined(STM32F101xG) || defined(STM32F103xE) || defined(STM32F103xG)
+#ifdef DATA_IN_ExtSRAM
+ static void SystemInit_ExtMemCtl(void);
+#endif /* DATA_IN_ExtSRAM */
+#endif /* STM32F100xE || STM32F101xE || STM32F101xG || STM32F103xE || STM32F103xG */
+
+/**
+ * @}
+ */
+
+/** @addtogroup STM32F1xx_System_Private_Functions
+ * @{
+ */
+
+/**
+ * @brief Setup the microcontroller system
+ * Initialize the Embedded Flash Interface, the PLL and update the
+ * SystemCoreClock variable.
+ * @note This function should be used only after reset.
+ * @param None
+ * @retval None
+ */
+void SystemInit (void)
+{
+#if defined(STM32F100xE) || defined(STM32F101xE) || defined(STM32F101xG) || defined(STM32F103xE) || defined(STM32F103xG)
+ #ifdef DATA_IN_ExtSRAM
+ SystemInit_ExtMemCtl();
+ #endif /* DATA_IN_ExtSRAM */
+#endif
+
+ /* Configure the Vector Table location -------------------------------------*/
+#if defined(USER_VECT_TAB_ADDRESS)
+ SCB->VTOR = VECT_TAB_BASE_ADDRESS | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM. */
+#endif /* USER_VECT_TAB_ADDRESS */
+}
+
+/**
+ * @brief Update SystemCoreClock variable according to Clock Register Values.
+ * The SystemCoreClock variable contains the core clock (HCLK), it can
+ * be used by the user application to setup the SysTick timer or configure
+ * other parameters.
+ *
+ * @note Each time the core clock (HCLK) changes, this function must be called
+ * to update SystemCoreClock variable value. Otherwise, any configuration
+ * based on this variable will be incorrect.
+ *
+ * @note - The system frequency computed by this function is not the real
+ * frequency in the chip. It is calculated based on the predefined
+ * constant and the selected clock source:
+ *
+ * - If SYSCLK source is HSI, SystemCoreClock will contain the HSI_VALUE(*)
+ *
+ * - If SYSCLK source is HSE, SystemCoreClock will contain the HSE_VALUE(**)
+ *
+ * - If SYSCLK source is PLL, SystemCoreClock will contain the HSE_VALUE(**)
+ * or HSI_VALUE(*) multiplied by the PLL factors.
+ *
+ * (*) HSI_VALUE is a constant defined in stm32f1xx.h file (default value
+ * 8 MHz) but the real value may vary depending on the variations
+ * in voltage and temperature.
+ *
+ * (**) HSE_VALUE is a constant defined in stm32f1xx.h file (default value
+ * 8 MHz or 25 MHz, depending on the product used), user has to ensure
+ * that HSE_VALUE is same as the real frequency of the crystal used.
+ * Otherwise, this function may have wrong result.
+ *
+ * - The result of this function could be not correct when using fractional
+ * value for HSE crystal.
+ * @param None
+ * @retval None
+ */
+void SystemCoreClockUpdate (void)
+{
+ uint32_t tmp = 0U, pllmull = 0U, pllsource = 0U;
+
+#if defined(STM32F105xC) || defined(STM32F107xC)
+ uint32_t prediv1source = 0U, prediv1factor = 0U, prediv2factor = 0U, pll2mull = 0U;
+#endif /* STM32F105xC */
+
+#if defined(STM32F100xB) || defined(STM32F100xE)
+ uint32_t prediv1factor = 0U;
+#endif /* STM32F100xB or STM32F100xE */
+
+ /* Get SYSCLK source -------------------------------------------------------*/
+ tmp = RCC->CFGR & RCC_CFGR_SWS;
+
+ switch (tmp)
+ {
+ case 0x00U: /* HSI used as system clock */
+ SystemCoreClock = HSI_VALUE;
+ break;
+ case 0x04U: /* HSE used as system clock */
+ SystemCoreClock = HSE_VALUE;
+ break;
+ case 0x08U: /* PLL used as system clock */
+
+ /* Get PLL clock source and multiplication factor ----------------------*/
+ pllmull = RCC->CFGR & RCC_CFGR_PLLMULL;
+ pllsource = RCC->CFGR & RCC_CFGR_PLLSRC;
+
+#if !defined(STM32F105xC) && !defined(STM32F107xC)
+ pllmull = ( pllmull >> 18U) + 2U;
+
+ if (pllsource == 0x00U)
+ {
+ /* HSI oscillator clock divided by 2 selected as PLL clock entry */
+ SystemCoreClock = (HSI_VALUE >> 1U) * pllmull;
+ }
+ else
+ {
+ #if defined(STM32F100xB) || defined(STM32F100xE)
+ prediv1factor = (RCC->CFGR2 & RCC_CFGR2_PREDIV1) + 1U;
+ /* HSE oscillator clock selected as PREDIV1 clock entry */
+ SystemCoreClock = (HSE_VALUE / prediv1factor) * pllmull;
+ #else
+ /* HSE selected as PLL clock entry */
+ if ((RCC->CFGR & RCC_CFGR_PLLXTPRE) != (uint32_t)RESET)
+ {/* HSE oscillator clock divided by 2 */
+ SystemCoreClock = (HSE_VALUE >> 1U) * pllmull;
+ }
+ else
+ {
+ SystemCoreClock = HSE_VALUE * pllmull;
+ }
+ #endif
+ }
+#else
+ pllmull = pllmull >> 18U;
+
+ if (pllmull != 0x0DU)
+ {
+ pllmull += 2U;
+ }
+ else
+ { /* PLL multiplication factor = PLL input clock * 6.5 */
+ pllmull = 13U / 2U;
+ }
+
+ if (pllsource == 0x00U)
+ {
+ /* HSI oscillator clock divided by 2 selected as PLL clock entry */
+ SystemCoreClock = (HSI_VALUE >> 1U) * pllmull;
+ }
+ else
+ {/* PREDIV1 selected as PLL clock entry */
+
+ /* Get PREDIV1 clock source and division factor */
+ prediv1source = RCC->CFGR2 & RCC_CFGR2_PREDIV1SRC;
+ prediv1factor = (RCC->CFGR2 & RCC_CFGR2_PREDIV1) + 1U;
+
+ if (prediv1source == 0U)
+ {
+ /* HSE oscillator clock selected as PREDIV1 clock entry */
+ SystemCoreClock = (HSE_VALUE / prediv1factor) * pllmull;
+ }
+ else
+ {/* PLL2 clock selected as PREDIV1 clock entry */
+
+ /* Get PREDIV2 division factor and PLL2 multiplication factor */
+ prediv2factor = ((RCC->CFGR2 & RCC_CFGR2_PREDIV2) >> 4U) + 1U;
+ pll2mull = ((RCC->CFGR2 & RCC_CFGR2_PLL2MUL) >> 8U) + 2U;
+ SystemCoreClock = (((HSE_VALUE / prediv2factor) * pll2mull) / prediv1factor) * pllmull;
+ }
+ }
+#endif /* STM32F105xC */
+ break;
+
+ default:
+ SystemCoreClock = HSI_VALUE;
+ break;
+ }
+
+ /* Compute HCLK clock frequency ----------------*/
+ /* Get HCLK prescaler */
+ tmp = AHBPrescTable[((RCC->CFGR & RCC_CFGR_HPRE) >> 4U)];
+ /* HCLK clock frequency */
+ SystemCoreClock >>= tmp;
+}
+
+#if defined(STM32F100xE) || defined(STM32F101xE) || defined(STM32F101xG) || defined(STM32F103xE) || defined(STM32F103xG)
+/**
+ * @brief Setup the external memory controller. Called in startup_stm32f1xx.s
+ * before jump to __main
+ * @param None
+ * @retval None
+ */
+#ifdef DATA_IN_ExtSRAM
+/**
+ * @brief Setup the external memory controller.
+ * Called in startup_stm32f1xx_xx.s/.c before jump to main.
+ * This function configures the external SRAM mounted on STM3210E-EVAL
+ * board (STM32 High density devices). This SRAM will be used as program
+ * data memory (including heap and stack).
+ * @param None
+ * @retval None
+ */
+void SystemInit_ExtMemCtl(void)
+{
+ __IO uint32_t tmpreg;
+ /*!< FSMC Bank1 NOR/SRAM3 is used for the STM3210E-EVAL, if another Bank is
+ required, then adjust the Register Addresses */
+
+ /* Enable FSMC clock */
+ RCC->AHBENR = 0x00000114U;
+
+ /* Delay after an RCC peripheral clock enabling */
+ tmpreg = READ_BIT(RCC->AHBENR, RCC_AHBENR_FSMCEN);
+
+ /* Enable GPIOD, GPIOE, GPIOF and GPIOG clocks */
+ RCC->APB2ENR = 0x000001E0U;
+
+ /* Delay after an RCC peripheral clock enabling */
+ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_IOPDEN);
+
+ (void)(tmpreg);
+
+/* --------------- SRAM Data lines, NOE and NWE configuration ---------------*/
+/*---------------- SRAM Address lines configuration -------------------------*/
+/*---------------- NOE and NWE configuration --------------------------------*/
+/*---------------- NE3 configuration ----------------------------------------*/
+/*---------------- NBL0, NBL1 configuration ---------------------------------*/
+
+ GPIOD->CRL = 0x44BB44BBU;
+ GPIOD->CRH = 0xBBBBBBBBU;
+
+ GPIOE->CRL = 0xB44444BBU;
+ GPIOE->CRH = 0xBBBBBBBBU;
+
+ GPIOF->CRL = 0x44BBBBBBU;
+ GPIOF->CRH = 0xBBBB4444U;
+
+ GPIOG->CRL = 0x44BBBBBBU;
+ GPIOG->CRH = 0x444B4B44U;
+
+/*---------------- FSMC Configuration ---------------------------------------*/
+/*---------------- Enable FSMC Bank1_SRAM Bank ------------------------------*/
+
+ FSMC_Bank1->BTCR[4U] = 0x00001091U;
+ FSMC_Bank1->BTCR[5U] = 0x00110212U;
+}
+#endif /* DATA_IN_ExtSRAM */
+#endif /* STM32F100xE || STM32F101xE || STM32F101xG || STM32F103xE || STM32F103xG */
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
--
Gitblit v1.9.1