//#include "stdio.h"
#include "timing_delay.h"
#include "gpio_i2c.h"
#include "board_uart.h"

#ifndef __LT8911EXB_H_
#define __LT8911EXB_H_

#define _uart_debug_
//#define _read_edid_ // read eDP panel EDID
//#define _Test_Pattern_
#define _LT8911_RSTN_LOW  GPIO_WriteLow(GPIOA , GPIO_PIN_1);
#define _LT8911_RSTN_High GPIO_WriteHigh(GPIOA , GPIO_PIN_1);

#define _eDP_2G7_
#define _link_train_enable_
#define _1080P_eDP_Panel_

//bool	ScrambleMode = 0;

#ifdef _1080P_eDP_Panel_

#define eDP_lane		2
#define PCR_PLL_PREDIV	0x40

// ¸ù¾ÝÇ°¶ËMIPIÐźŵÄTiming£¬ÐÞ¸ÄÒÔϲÎÊý£º
//According to the timing of the Mipi signal, modify the following parameters:
static int MIPI_Timing[] =
// hfp,	hs,	hbp,	hact,	htotal,	vfp,	vs,	vbp,	vact,	vtotal,	pixel_CLK/10000
{ 48,32,147,1920,2187,3,6,51,1080,1140,14960 };

#define _8bit_                                              // eDP panel Color Depth£¬16.7M color

#endif

#define _Nvid 0         // 0: 0x0080,default
static int Nvid_Val[] = { 0x0080, 0x0800 };

#define _MIPI_Lane_ 4   // 3 /2 / 1
#define _MIPI_data_PN_Swap_En	0xF0
#define _MIPI_data_PN_Swap_Dis	0x00
#define _MIPI_data_PN_ _MIPI_data_PN_Swap_Dis
#define _No_swap_			0x00    // 3210 default
#define _MIPI_data_3210_	0       // default
#define _MIPI_data_0123_	21
#define _MIPI_data_2103_	20
#define _MIPI_data_sequence_ _No_swap_

#define _eDP_data_No_swap_	 0xe4 // default
#define _eDP_data_sequence_ _eDP_data_No_swap_ // default, no swap

#define _eDP_data_PN_Swap_En	0xF0 // Please refer to the notes below
#define _eDP_data_PN_Swap_Dis	0x00
#define _eDP_data_PN_ _eDP_data_PN_Swap_Dis // defailt ; disable

extern bool ScrambleMode;
extern bool	flag_mipi_on;
#ifdef _read_edid_ // read eDP panel EDID

extern u8		EDID_DATA[128];
extern u16	EDID_Timing[11];

extern bool	EDID_Reply;
#endif

enum {
	hfp = 0,
	hs,
	hbp,
	hact,
	htotal,
	vfp,
	vs,
	vbp,
	vact,
	vtotal,
	pclk_10khz
};

enum
{
	_Level0_ = 0,                                               // 27.8 mA  0x83/0x00
	_Level1_,                                                   // 26.2 mA  0x82/0xe0
	_Level2_,                                                   // 24.6 mA  0x82/0xc0
	_Level3_,                                                   // 23 mA    0x82/0xa0
	_Level4_,                                                   // 21.4 mA  0x82/0x80
	_Level5_,                                                   // 18.2 mA  0x82/0x40
	_Level6_,                                                   // 16.6 mA  0x82/0x20
	_Level7_,                                                   // 15mA     0x82/0x00  // level 1
	_Level8_,                                                   // 12.8mA   0x81/0x00  // level 2
	_Level9_,                                                   // 11.2mA   0x80/0xe0  // level 3
	_Level10_,                                                  // 9.6mA    0x80/0xc0  // level 4
	_Level11_,                                                  // 8mA      0x80/0xa0  // level 5
	_Level12_                                                  // 6mA      0x80/0x80  // level 6
};

extern u8	Swing_Setting1[];
extern u8	Swing_Setting2[];
extern u8	Level;                                          // normal

extern void LT8911EXB_GPIO_Init(void);
extern void Reset_LT8911EXB( void );
extern void LT8911EX_ChipID( void );
extern void LT8911EXB_MIPI_Video_Timing( void );
extern void LT8911EXB_eDP_Video_cfg( void );
extern void LT8911EXB_init( void );
extern void LT8911EXB_read_edid( void );
extern void LT8911EX_TxSwingPreSet( void );
extern void DpcdWrite( u32 Address, u8 Data );
extern void LT8911EX_link_train( void );
extern void LT8911EXB_LinkTrainResultCheck( void );
extern void LT8911EXB_video_check( void );
extern u8 DpcdRead( u32 Address );
extern void PCR_Status( void ); 
#endif